Certificate IV in Telecommunications Engineering Technology and Certificate IV in Project Management Practices
ICT41215 & BSB41515
This course is for those who want to be part of the Internet of Things (IoT), which will enable the connection of anything, anytime, anyone, any place, any service and any network. 
Your gateway to the Internet of Things
This course will prepare you for the IoT by giving you the skills that underpin it:
Funding, Incentives and Subsidies
MILCOM is approved for a range of government funding programs in a number of States and Territories. Contact us on 1300 369 320 to find out whether this program is available under funding and whether you may be eligible.Learning Outcomes
After successfully completing this course, you will be able to:
- Design, install and maintain networks in emerging and converging technologies
- install and maintain internet protocol (IP) based network telecommunications equipment
- install IP based networks in home networks and small and medium enterprises
- Design the cabling infrastructure to support the convergent technologies
- Design the telecommunications access network cabling infrastructure, systems and basic customer premises equipment
- assess installation requirements of converging voice, video and data IP networks
- plan and perform installations of convergent residential and commercial technologies
- test installed equipment and fault find
Units of Competency
After successful completion of this course, you will be issued with the Nationally Recognised Qualification
ICT41215 Certificate IV in Telecommunications Engineering Technology and BSB41515 Certificate IV in Project Management Practices.
For successful completion of this course, you need to complete and demonstrate competency in these units of competency:
- ICTICT408 Create technical documentation
- ICTPMG403 Manage the delivery of network infrastructure
- ICTTEN201 Use electrical skills in telecommunications work
- ICTTEN202 Use hand and power tools
- ICTTEN410 Locate, and rectify faults
- ICTTEN414 Repair telecommunication system faults
- ICTWHS204 Follow work health and safety and environmental policy and procedures
- ICTWOR201 Work effectively in telecommunications technology
- ICTTEN402 Estimate and quote for customer telecommunications equipment installation
- BSBCUS402 Address customer needs
- ICTTEN401 Identify requirements for customer telecommunications equipment
- ICTCBL401 Prepare design drawings and specification for a cable installation
- ICTTEN425 Design, install and configure a customer smart technology network
- ICTTEN416 Install, configure and test an internet protocol network
- ICTTEN405 Install configuration programs on PC based customer equipment
- ICTTEN406 Effect changes to existing customer premises equipment systems and equipment
- BSBPMG409 Apply project scope management techniques
- BSBPMG410 Apply project time management techniques
- BSBPMG411 Apply project quality management techniques
- BSBPMG412 Apply project cost management techniques
- BSBPMG413 Apply project human resources management approaches
- BSBPMG414 Apply project information management and communications techniques
- BSBPMG415 Apply project risk management techniques
- BSBPMG416 Apply project procurement procedures
- BSBPMG417 Apply project life cycle management processes
- BSBPMG418 Apply project stakeholder engagement technique
Course Duration and Delivery Method
This qualification is delivered as blended learning with face-to-face sessions held at the MILCOM training centre over 12 months (not including holiday breaks). Learners will work through course material with a trainer and complete assessments during class and during non-class allocated time. Classes may be scheduled at alternative, mutually convenient and suitable locations and can be contextualised for a sufficiently large groups of participants.
You will be required to attend a Milcom Institute’s training rooms for a total of 21 days. The attendance is in the following blocks:
| Block 1 - Smart Wired | 4 days |
| Block 2 - IP | 3 days |
| Block 4 - KNX | 5 days |
| Block 5 - BICSI Telecommunications Project Management | 5 days |
| Block 6 - Assessment preparation and assessment | 4 days |
Pre-requisite
Whilst there are no pre-requisites under the approved training package for this course, it is strongly recommended that anyone applying for the course has completed:
- ICTCBL2136B Install, maintain and modify customer premises communications cabling: ACMA Restricted Rule (where ACMA Restricted Registration is necessary)
- ICTCBL2137B Install, maintain and modify customer premises communications cabling: ACMA Open Rule
- ICTCBL3009B Install, terminate and certify structured cabling installation
- ICTCBL3011B Install and terminate coaxial cable OR Be a licenced electrician
KNX accreditation – no pre-requisite
BICSI Registered Telecommunications Project Manager (RTPM) accreditation – for students intending to sit for the BICSI
RTPM exam, they must comply with the following pre requisite:
BICSI REQUIREMENT
To sit for the RTPM exam, you must first have:
A minimum of two years of approved and verifiable experience in Project Management, such as planning, execution, and closing of any project. The PM experience does not have to be directly related to telecommunications, but telecommunications experience is a plus. Experience must be within the last six years.
To apply for the exam, the applicant will need to complete the BICSI RTPM application that can be downloaded from
https://www.bicsi.org/double.aspx?l=5338&r=5340
Fees
Student enrolment fee is
$2,000 for students eligible to access funding form the Victorian State Government Training Guarantee, or $8,500 for all other students.
- 1. Access to the blended delivery course
- 2. Student resources which includes:
- a. KNX Course ware
- b. KNX assessment
- c. Telecommunications Project Management (TMP) Reference
- d. A guide to the Project Management Book of Knowledge’s
- e. Project Management: A Systems Approach to Planning, Scheduling, and Controlling
- f. Smart Wired Code of Practice
- 3. KNX assessment to gain the accreditation
- 4. KNX student licences
- 5. BICSI individual membership for one year
- 6. IP networking
For Students wishing to undertake the BICSI RTPM assessment at the completion of the course, there is an additional fee of $385 and will need to complete the BICSI RTPM application form. To apply for the exam, the applicant will need to complete the BICSI RTPM application that can be downloaded from https://www.bicsi.org/double.aspx?l=5338&r=5340.